#
# Physical Layer USB driver configuration
#
menu "USB Physical Layer drivers"
config USB_PHY
def_bool n
#
# USB Transceiver Drivers
#
config AB8500_USB
tristate "AB8500 USB Transceiver Driver"
depends on AB8500_CORE
select USB_PHY
help
Enable this to support the USB OTG transceiver in AB8500 chip.
This transceiver supports high and full speed devices plus,
in host mode, low speed.
config FSL_USB2_OTG
bool "Freescale USB OTG Transceiver Driver"
depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
select USB_PHY
help
Enable this to support Freescale USB OTG transceiver.
config ISP1301_OMAP
tristate "Philips ISP1301 with OMAP OTG"
depends on I2C && ARCH_OMAP_OTG
depends on USB
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
select USB_PHY
help
If you say yes here you get support for the Philips ISP1301
USB-On-The-Go transceiver working with the OMAP OTG controller.
The ISP1301 is a full speed USB transceiver which is used in
products including H2, H3, and H4 development boards for Texas
Instruments OMAP processors.
This driver can also be built as a module. If so, the module
will be called phy-isp1301-omap.
config KEYSTONE_USB_PHY
tristate "Keystone USB PHY Driver"
depends on ARCH_KEYSTONE || COMPILE_TEST
depends on NOP_USB_XCEIV
help
Enable this to support Keystone USB phy. This driver provides
interface to interact with USB 2.0 and USB 3.0 PHY that is part
of the Keystone SOC.
config NOP_USB_XCEIV
tristate "NOP USB Transceiver Driver"
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
select USB_PHY
help
This driver is to be used by all the usb transceiver which are either
built-in with usb ip or which are autonomous and doesn't require any
phy programming such as ISP1x04 etc.
config AM335X_CONTROL_USB
tristate
config AM335X_PHY_USB
tristate "AM335x USB PHY Driver"
depends on ARM || COMPILE_TEST
depends on NOP_USB_XCEIV
select USB_PHY
select AM335X_CONTROL_USB
select USB_COMMON
help
This driver provides PHY support for that phy which part for the
AM335x SoC.
config SAMSUNG_USBPHY
tristate
help
Enable this to support Samsung USB phy helper driver for Samsung SoCs.
This driver provides common interface to interact, for Samsung USB 2.0 PHY
driver and later for Samsung USB 3.0 PHY driver.
config TWL6030_USB
tristate "TWL6030 USB Transceiver Driver"
depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
depends on OF
help
Enable this to support the USB OTG transceiver on TWL6030
family chips. This TWL6030 transceiver has the VBUS and ID GND
and OTG SRP events capabilities. For all other transceiver functionality
UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
are hooked to this driver through platform_data structure.
The definition of internal PHY APIs are in the mach-omap2 layer.
config USB_GPIO_VBUS
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
depends on GPIOLIB || COMPILE_TEST
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
select USB_PHY
help
Provides simple GPIO VBUS sensing for controllers with an
internal transceiver via the usb_phy interface, and
optionally control of a D+ pullup GPIO as well as a VBUS
current limit regulator.
config OMAP_OTG
tristate "OMAP USB OTG controller driver"
depends on ARCH_OMAP_OTG && EXTCON
help
Enable this to support some transceivers on OMAP1 platforms. OTG
controller is needed to switch between host and peripheral modes.
This driver can also be built as a module. If so, the module
will be called phy-omap-otg.
config TAHVO_USB
tristate "Tahvo USB transceiver driver"
depends on MFD_RETU && EXTCON
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
select USB_PHY
help
Enable this to support USB transceiver on Tahvo. This is used
at least on Nokia 770.
config TAHVO_USB_HOST_BY_DEFAULT
depends on TAHVO_USB
bool "Device in USB host mode by default"
help
Say Y here, if you want the device to enter USB host mode
by default on bootup.
config USB_ISP1301
tristate "NXP ISP1301 USB transceiver support"
depends on USB || USB_GADGET
depends on I2C
select USB_PHY
help
Say Y here to add support for the NXP ISP1301 USB transceiver driver.
This chip is typically used as USB transceiver for USB host, gadget
and OTG drivers (to be selected separately).
To compile this driver as a module, choose M here: the
module will be called phy-isp1301.
config USB_MSM_OTG
tristate "Qualcomm on-chip USB OTG controller support"
depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST)
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
depends on RESET_CONTROLLER
depends on EXTCON
select USB_PHY
help
Enable this to support the USB OTG transceiver on Qualcomm chips. It
handles PHY initialization, clock management, and workarounds
required after resetting the hardware and power management.
This driver is required even for peripheral only or host only
mode configurations.
This driver is not supported on boards like trout which
has an external PHY.
config USB_QCOM_8X16_PHY
tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support"
depends on ARCH_QCOM || COMPILE_TEST
depends on RESET_CONTROLLER && EXTCON
select USB_PHY
select USB_ULPI_VIEWPORT
help
Enable this to support the USB transceiver on Qualcomm 8x16 chipsets.
It handles PHY initialization, clock management, power management,
and workarounds required after resetting the hardware.
To compile this driver as a module, choose M here: the
module will be called phy-qcom-8x16-usb.
config USB_MV_OTG
tristate "Marvell USB OTG support"
depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
select USB_PHY
help
Say Y here if you want to build Marvell USB OTG transciever
driver in kernel (including PXA and MMP series). This driver
implements role switch between EHCI host driver and gadget driver.
To compile this driver as a module, choose M here.
config USB_MXS_PHY
tristate "Freescale MXS USB PHY support"
depends on ARCH_MXC || ARCH_MXS
select STMP_DEVICE
select USB_PHY
help
Enable this to support the Freescale MXS USB PHY.
MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
config USB_ULPI
bool "Generic ULPI Transceiver Driver"
depends on ARM || ARM64
select USB_ULPI_VIEWPORT
help
Enable this to support ULPI connected USB OTG transceivers which
are likely found on embedded boards.
config USB_ULPI_VIEWPORT
bool
help
Provides read/write operations to the ULPI phy register set for
controllers with a viewport register (e.g. Chipidea/ARC controllers).
endmenu
oundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@gmail.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: anton@ozlabs.org
Cc: namhyung@kernel.org
Cc: stable@vger.kernel.org # v3.16+
Fixes: f972eb63b100 ("perf: Pass protection and flags bits through mmap2 interface")
Link: http://lkml.kernel.org/r/20170126221508.GF6536@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>