| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some CAN controllers don't implement a FIFO in hardware, but fill their
mailboxes in a particular order (from lowest to highest or highest to lowest).
This makes problems to read the frames in the correct order from the hardware,
as new frames might be filled into just read (low) mailboxes. This gets worse,
when following new frames are received into not read (higher) mailboxes.
On the bright side some these CAN controllers put a timestamp on each received
CAN frame. This patch adds support to offload CAN frames in interrupt context,
order them by timestamp and then transmitted in a NAPI context.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some CAN controllers have a usable FIFO already but can still benefit
from off-loading the CAN controller FIFO. The CAN frames of the FIFO are
read and put into a skb queue during interrupt and then transmitted in a
NAPI context.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
All __napi_complete() callers have been converted to
use the more standard napi_complete_done(),
we can now remove this NAPI method for good.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change ip6_route_multipath_add to send one notifciation with the full
route encoded with RTA_MULTIPATH instead of a series of individual routes.
This is done by adding a skip_notify flag to the nl_info struct. The
flag is used to skip sending of the notification in the fib code that
actually inserts the route. Once the full route has been added, a
notification is generated with all nexthops.
ip6_route_multipath_add handles 3 use cases: new routes, route replace,
and route append. The multipath notification generated needs to be
consistent with the order of the nexthops and it should be consistent
with the order in a FIB dump which means the route with the first nexthop
needs to be used as the route reference. For the first 2 cases (new and
replace), a reference to the route used to send the notification is
obtained by saving the first route added. For the append case, the last
route added is used to loop back to its first sibling route which is
the first nexthop in the multipath route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv4 allows multipath routes to be deleted using just the prefix and
length. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.11.200.2 dev eth11.200 weight 1
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
$ ip ro del 1.1.1.0/24 vrf red
$ ip ro ls vrf red
unreachable default metric 8192
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
The same notation does not work with IPv6 because of how multipath routes
are implemented for IPv6. For IPv6 only the first nexthop of a multipath
route is deleted if the request contains only a prefix and length. This
leads to unnecessary complexity in userspace dealing with IPv6 multipath
routes.
This patch allows all nexthops to be deleted without specifying each one
in the delete request. Internally, this is done by walking the sibling
list of the route matching the specifications given (prefix, length,
metric, protocol, etc).
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 via 2001:db8:1::2 dev eth1 metric 1024 pref medium
2001:db8:200::/120 via 2001:db8:2::2 dev eth2 metric 1024 pref medium
...
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
...
Because IPv6 allows individual nexthops to be deleted without deleting
the entire route, the ip6_route_multipath_del and non-multipath code
path (ip6_route_del) have to be discriminated so that all nexthops are
only deleted for the latter case. This is done by making the existing
fc_type in fib6_config a u16 and then adding a new u16 field with
fc_delete_all_nh as the first bit.
Suggested-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We added generic support for busy polling in NAPI layer in linux-4.5
No network driver uses ndo_busy_poll() anymore, we can get rid
of the pointer in struct net_device_ops, and its use in sk_busy_loop()
Saves NETIF_F_BUSY_POLL features bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, they are:
1) Stash ctinfo 3-bit field into pointer to nf_conntrack object from
sk_buff so we only access one single cacheline in the conntrack
hotpath. Patchset from Florian Westphal.
2) Don't leak pointer to internal structures when exporting x_tables
ruleset back to userspace, from Willem DeBruijn. This includes new
helper functions to copy data to userspace such as xt_data_to_user()
as well as conversions of our ip_tables, ip6_tables and arp_tables
clients to use it. Not surprinsingly, ebtables requires an ad-hoc
update. There is also a new field in x_tables extensions to indicate
the amount of bytes that we copy to userspace.
3) Add nf_log_all_netns sysctl: This new knob allows you to enable
logging via nf_log infrastructure for all existing netnamespaces.
Given the effort to provide pernet syslog has been discontinued,
let's provide a way to restore logging using netfilter kernel logging
facilities in trusted environments. Patch from Michal Kubecek.
4) Validate SCTP checksum from conntrack helper, from Davide Caratti.
5) Merge UDPlite conntrack and NAT helpers into UDP, this was mostly
a copy&paste from the original helper, from Florian Westphal.
6) Reset netfilter state when duplicating packets, also from Florian.
7) Remove unnecessary check for broadcast in IPv6 in pkttype match and
nft_meta, from Liping Zhang.
8) Add missing code to deal with loopback packets from nft_meta when
used by the netdev family, also from Liping.
9) Several cleanups on nf_tables, one to remove unnecessary check from
the netlink control plane path to add table, set and stateful objects
and code consolidation when unregister chain hooks, from Gao Feng.
10) Fix harmless reference counter underflow in IPVS that, however,
results in problems with the introduction of the new refcount_t
type, from David Windsor.
11) Enable LIBCRC32C from nf_ct_sctp instead of nf_nat_sctp,
from Davide Caratti.
12) Missing documentation on nf_tables uapi header, from Liping Zhang.
13) Use rb_entry() helper in xt_connlimit, from Geliang Tang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver that offloads flower rules needs to know with which priority
user inserted the rules. So add this information into offload struct.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This introduces a infrastructure for management of linear priority
areas. Priority order in an array matters, however order of items inside
a priority group does not matter.
As an initial implementation, L-sort algorithm is used. It is quite
trivial. More advanced algorithm called P-sort will be introduced as a
follow-up. The infrastructure is prepared for other algos.
Alongside this, a testing module is introduced as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to list_for_each_entry_continue and its reverse variant
list_for_each_entry_continue_reverse, introduce reverse helper for
list_for_each_entry_from.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Steven suggested to improve trace_print_hex_seq() a bit after commit
2acae0d5b0f7 ("trace: add variant without spacing in trace_print_hex_seq")
in two ways: i) by adding a kdoc comment for the helper function
itself and ii) by renaming 'spacing' argument into 'concatenate'
to better denote that we don't add spaces between each hex bytes.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New nested netlink attribute to associate tunnel info per vlan.
This is used by bridge driver to send tunnel metadata to
bridge ports in vlan tunnel mode. This patch also adds new per
port flag IFLA_BRPORT_VLAN_TUNNEL to enable vlan tunnel mode.
off by default.
One example use for this is a vxlan bridging gateway or vtep
which maps vlans to vn-segments (or vnis). User can configure
per-vlan tunnel information which the bridge driver can use
to bridge vlan into the corresponding vn-segment.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vxlan COLLECT_METADATA mode today solves the per-vni netdev
scalability problem in l3 networks. It expects all forwarding
information to be present in dst_metadata. This patch series
enhances collect metadata mode to include the case where only
vni is present in dst_metadata, and the vxlan driver can then use
the rest of the forwarding information datbase to make forwarding
decisions. There is no change to default COLLECT_METADATA
behaviour. These changes only apply to COLLECT_METADATA when
used with the bridging use-case with a special dst_metadata
tunnel info flag (eg: where vxlan device is part of a bridge).
For all this to work, the vxlan driver will need to now support a
single fdb table hashed by mac + vni. This series essentially makes
this happen.
use-case and workflow:
vxlan collect metadata device participates in bridging vlan
to vn-segments. Bridge driver above the vxlan device,
sends the vni corresponding to the vlan in the dst_metadata.
vxlan driver will lookup forwarding database with (mac + vni)
for the required remote destination information to forward the
packet.
Changes introduced by this patch:
- allow learning and forwarding database state in vxlan netdev in
COLLECT_METADATA mode. Current behaviour is not changed
by default. tunnel info flag IP_TUNNEL_INFO_BRIDGE is used
to support the new bridge friendly mode.
- A single fdb table hashed by (mac, vni) to allow fdb entries with
multiple vnis in the same fdb table
- rx path already has the vni
- tx path expects a vni in the packet with dst_metadata
- prior to this series, fdb remote_dsts carried remote vni and
the vxlan device carrying the fdb table represented the
source vni. With the vxlan device now representing multiple vnis,
this patch adds a src vni attribute to the fdb entry. The remote
vni already uses NDA_VNI attribute. This patch introduces
NDA_SRC_VNI netlink attribute to represent the src vni in a multi
vni fdb table.
iproute2 example (patched and pruned iproute2 output to just show
relevant fdb entries):
example shows same host mac learnt on two vni's.
before (netdev per vni):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self
after this patch with collect metadata in bridged mode (single netdev):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New ip_tunnel_info flag to represent bridged tunnel metadata.
Used by bridge driver later in the series to pass per vlan dst
metadata to bridge ports.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the encode/decode functionality from the ife module instead of using
implementation inside the act_ife.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This module is responsible for the ife encapsulation protocol
encode/decode logics. That module can:
- ife_encode: encode skb and reserve space for the ife meta header
- ife_decode: decode skb and extract the meta header size
- ife_tlv_meta_encode - encodes one tlv entry into the reserved ife
header space.
- ife_tlv_meta_decode - decodes one tlv entry from the packet
- ife_tlv_meta_next - advance to the next tlv
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the function ife_tlv_meta_encode is not used by any other module,
unexport it and make it static for the act_ife module.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Small cleanup factorizing code doing the TCP_MAXSEG clamping.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Debugging issues caused by pfmemalloc is often tedious.
Add a new SNMP counter to more easily diagnose these problems.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Josef Bacik <jbacik@fb.com>
Acked-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 88e1545 PHYs are discrete Marvell PHYs, found in a quad package on
the zii-devel-b board. Add support for it to the Marvell PHY driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This ioctl opens a file to which a socket is bound and
returns a file descriptor. The caller has to have CAP_NET_ADMIN
in the socket network namespace.
Currently it is impossible to get a path and a mount point
for a socket file. socket_diag reports address, device ID and inode
number for unix sockets. An address can contain a relative path or
a file may be moved somewhere. And these properties say nothing about
a mount namespace and a mount point of a socket file.
With the introduced ioctl, we can get a path by reading
/proc/self/fd/X and get mnt_id from /proc/self/fdinfo/X.
In CRIU we are going to use this ioctl to dump and restore unix socket.
Here is an example how it can be used:
$ strace -e socket,bind,ioctl ./test /tmp/test_sock
socket(AF_UNIX, SOCK_STREAM, 0) = 3
bind(3, {sa_family=AF_UNIX, sun_path="test_sock"}, 11) = 0
ioctl(3, SIOCUNIXFILE, 0) = 4
^Z
$ ss -a | grep test_sock
u_str LISTEN 0 1 test_sock 17798 * 0
$ ls -l /proc/760/fd/{3,4}
lrwx------ 1 root root 64 Feb 1 09:41 3 -> 'socket:[17798]'
l--------- 1 root root 64 Feb 1 09:41 4 -> /tmp/test_sock
$ cat /proc/760/fdinfo/4
pos: 0
flags: 012000000
mnt_id: 40
$ cat /proc/self/mountinfo | grep "^40\s"
40 19 0:37 / /tmp rw shared:23 - tmpfs tmpfs rw
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6390 Ethernet switch has internal PHYs. These PHYs don't have
an model ID in the ID2 register. So the MDIO driver in the switch
intercepts reads to this register, and returns the switch family ID.
Extend the Marvell PHY driver by including this ID, and treat the PHY
as a 88E1540.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All merge conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 69b34fb996b2 ("netfilter: xt_LOG: add net namespace support for
xt_LOG") disabled logging packets using the LOG target from non-init
namespaces. The motivation was to prevent containers from flooding
kernel log of the host. The plan was to keep it that way until syslog
namespace implementation allows containers to log in a safe way.
However, the work on syslog namespace seems to have hit a dead end
somewhere in 2013 and there are users who want to use xt_LOG in all
network namespaces. This patch allows to do so by setting
/proc/sys/net/netfilter/nf_log_all_netns
to a nonzero value. This sysctl is only accessible from init_net so that
one cannot switch the behaviour from inside a container.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently, the ip_vs_dest cache frees ip_vs_dest objects when their
reference count becomes < 0. Aside from not being semantically sound,
this is problematic for the new type refcount_t, which will be introduced
shortly in a separate patch. refcount_t is the new kernel type for
holding reference counts, and provides overflow protection and a
constrained interface relative to atomic_t (the type currently being
used for kernel reference counts).
Per Julian Anastasov: "The problem is that dest_trash currently holds
deleted dests (unlinked from RCU lists) with refcnt=0." Changing
dest_trash to hold dest with refcnt=1 will allow us to free ip_vs_dest
structs when their refcnt=0, in ip_vs_dest_put_and_free().
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
After this change conntrack operations (lookup, creation, matching from
ruleset) only access one instead of two sk_buff cache lines.
This works for normal conntracks because those are allocated from a slab
that guarantees hw cacheline or 8byte alignment (whatever is larger)
so the 3 bits needed for ctinfo won't overlap with nf_conn addresses.
Template allocation now does manual address alignment (see previous change)
on arches that don't have sufficent kmalloc min alignment.
Some spots intentionally use skb->_nfct instead of skb_nfct() helpers,
this is to avoid undoing the skb_nfct() use when we remove untracked
conntrack object in the future.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The next change will merge skb->nfct pointer and skb->nfctinfo
status bits into single skb->_nfct (unsigned long) area.
For this to work nf_conn addresses must always be aligned at least on
an 8 byte boundary since we will need the lower 3bits to store nfctinfo.
Conntrack templates are allocated via kmalloc.
kbuild test robot reported
BUILD_BUG_ON failed: NFCT_INFOMASK >= ARCH_KMALLOC_MINALIGN
on v1 of this patchset, so not all platforms meet this requirement.
Do manual alignment if needed, the alignment offset is stored in the
nf_conn entry protocol area. This works because templates are not
handed off to L4 protocol trackers.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add a helper to assign a nf_conn entry and the ctinfo bits to an sk_buff.
This avoids changing code in followup patch that merges skb->nfct and
skb->nfctinfo into skb->_nfct.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Followup patch renames skb->nfct and changes its type so add a helper to
avoid intrusive rename change later.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Next patch makes direct skb->nfct access illegal, reduce noise
in next patch by using accessors we already have.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
It is never accessed for reading and the only places that write to it
are the icmp(6) handlers, which also set skb->nfct (and skb->nfctinfo).
The conntrack core specifically checks for attached skb->nfct after
->error() invocation and returns early in this case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|