#ifndef CM9780_H_INCLUDED
#define CM9780_H_INCLUDED
#define CM9780_JACK 0x62
#define CM9780_MIXER 0x64
#define CM9780_GPIO_SETUP 0x70
#define CM9780_GPIO_STATUS 0x72
/* jack control */
#define CM9780_RSOE 0x0001
#define CM9780_CBOE 0x0002
#define CM9780_SSOE 0x0004
#define CM9780_FROE 0x0008
#define CM9780_HP2FMICOE 0x0010
#define CM9780_CB2MICOE 0x0020
#define CM9780_FMIC2LI 0x0040
#define CM9780_FMIC2MIC 0x0080
#define CM9780_HP2LI 0x0100
#define CM9780_HP2MIC 0x0200
#define CM9780_MIC2LI 0x0400
#define CM9780_MIC2MIC 0x0800
#define CM9780_LI2LI 0x1000
#define CM9780_LI2MIC 0x2000
#define CM9780_LO2LI 0x4000
#define CM9780_LO2MIC 0x8000
/* mixer control */
#define CM9780_BSTSEL 0x0001
#define CM9780_STRO_MIC 0x0002
#define CM9780_SPDI_FREX 0x0004
#define CM9780_SPDI_SSEX 0x0008
#define CM9780_SPDI_CBEX 0x0010
#define CM9780_SPDI_RSEX 0x0020
#define CM9780_MIX2FR 0x0040
#define CM9780_MIX2SS 0x0080
#define CM9780_MIX2CB 0x0100
#define CM9780_MIX2RS 0x0200
#define CM9780_MIX2FR_EX 0x0400
#define CM9780_MIX2SS_EX 0x0800
#define CM9780_MIX2CB_EX 0x1000
#define CM9780_MIX2RS_EX 0x2000
#define CM9780_P47_IO 0x4000
#define CM9780_PCBSW 0x8000
/* GPIO setup */
#define CM9780_GPI0EN 0x0001
#define CM9780_GPI1EN 0x0002
#define CM9780_SENSE_P 0x0004
#define CM9780_LOCK_P 0x0008
#define CM9780_GPIO0P 0x0010
#define CM9780_GPIO1P 0x0020
#define CM9780_GPIO0IO 0x0100
#define CM9780_GPIO1IO 0x0200
/* GPIO status */
#define CM9780_GPO0 0x0001
#define CM9780_GPO1 0x0002
#define CM9780_GPIO0S 0x0010
#define CM9780_GPIO1S 0x0020
#define CM9780_GPII0S 0x0100
#define CM9780_GPII1S 0x0200
#endif
fd1d141db320db970aace7f0'>refslogtreecommitdiff
sh_eth: rename EESIPR bits
Since the commit b0ca2a21f769 ("sh_eth: Add support of SH7763 to sh_eth")
the *enum* declaring the EESIPR bits (interrupt mask) went out of sync with
the *enum* declaring the EESR bits (interrupt status) WRT bit naming and
formatting. I'd like to restore the consistency by using EESIPR as the bit
name prefix, renaming the *enum* to EESIPR_BIT, and (finally) renaming the
bits according to the available Renesas SH77{34|63} manuals; additionally,
reconstruct couple names using the EESR bit declaration above...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>