config SND_ATMEL_SOC
tristate "SoC Audio for the Atmel System-on-Chip"
depends on HAS_IOMEM
help
Say Y or M if you want to add support for codecs attached to
the ATMEL SSC interface. You will also need
to select the audio interfaces to support below.
if SND_ATMEL_SOC
config SND_ATMEL_SOC_PDC
tristate
depends on HAS_DMA
default m if SND_ATMEL_SOC_SSC_PDC=m && SND_ATMEL_SOC_SSC=m
default y if SND_ATMEL_SOC_SSC_PDC=y || (SND_ATMEL_SOC_SSC_PDC=m && SND_ATMEL_SOC_SSC=y)
config SND_ATMEL_SOC_SSC_PDC
tristate
config SND_ATMEL_SOC_DMA
tristate
select SND_SOC_GENERIC_DMAENGINE_PCM
default m if SND_ATMEL_SOC_SSC_DMA=m && SND_ATMEL_SOC_SSC=m
default y if SND_ATMEL_SOC_SSC_DMA=y || (SND_ATMEL_SOC_SSC_DMA=m && SND_ATMEL_SOC_SSC=y)
config SND_ATMEL_SOC_SSC_DMA
tristate
config SND_ATMEL_SOC_SSC
tristate
default y if SND_ATMEL_SOC_SSC_DMA=y || SND_ATMEL_SOC_SSC_PDC=y
default m if SND_ATMEL_SOC_SSC_DMA=m || SND_ATMEL_SOC_SSC_PDC=m
config SND_AT91_SOC_SAM9G20_WM8731
tristate "SoC Audio support for WM8731-based At91sam9g20 evaluation board"
depends on ARCH_AT91 || COMPILE_TEST
depends on ATMEL_SSC && SND_SOC_I2C_AND_SPI
select SND_ATMEL_SOC_SSC_PDC
select SND_SOC_WM8731
help
Say Y if you want to add support for SoC audio on WM8731-based
AT91sam9g20 evaluation board.
config SND_ATMEL_SOC_WM8904
tristate "Atmel ASoC driver for boards using WM8904 codec"
depends on ARCH_AT91 || COMPILE_TEST
depends on ATMEL_SSC && I2C
select SND_ATMEL_SOC_SSC_DMA
select SND_SOC_WM8904
help
Say Y if you want to add support for Atmel ASoC driver for boards using
WM8904 codec.
config SND_AT91_SOC_SAM9X5_WM8731
tristate "SoC Audio support for WM8731-based at91sam9x5 board"
depends on ARCH_AT91 || COMPILE_TEST
depends on ATMEL_SSC && SND_SOC_I2C_AND_SPI
select SND_ATMEL_SOC_SSC_DMA
select SND_SOC_WM8731
help
Say Y if you want to add support for audio SoC on an
at91sam9x5 based board that is using WM8731 codec.
config SND_ATMEL_SOC_CLASSD
tristate "Atmel ASoC driver for boards using CLASSD"
depends on ARCH_AT91 || COMPILE_TEST
select SND_ATMEL_SOC_DMA
select REGMAP_MMIO
help
Say Y if you want to add support for Atmel ASoC driver for boards using
CLASSD.
config SND_ATMEL_SOC_PDMIC
tristate "Atmel ASoC driver for boards using PDMIC"
depends on OF && (ARCH_AT91 || COMPILE_TEST)
select SND_SOC_GENERIC_DMAENGINE_PCM
select REGMAP_MMIO
help
Say Y if you want to add support for Atmel ASoC driver for boards using
PDMIC.
config SND_ATMEL_SOC_TSE850_PCM5142
tristate "ASoC driver for the Axentia TSE-850"
depends on ARCH_AT91 && OF
depends on ATMEL_SSC && I2C
select SND_ATMEL_SOC_SSC_DMA
select SND_SOC_PCM512x_I2C
help
Say Y if you want to add support for the ASoC driver for the
Axentia TSE-850 with a PCM5142 codec.
endif
orm>
Merge branch 'sh_eth-E-DMAC-interrupt-mask-cleanups'
Sergei Shtylyov says:
====================
sh_eth: E-DMAC interrupt mask cleanups
Here's a set of 3 patches against DaveM's 'net-next.git' repo. The main goal
of this set is to stop using the bare numbers for the E-DMAC interrupt masks.
[1/3] sh_eth: rename EESIPR bits
[2/3] sh_eth: add missing EESIPR bits
[3/3] sh_eth: stop using bare numbers for EESIPR values
====================
Signed-off-by: David S. Miller <davem@davemloft.net>