diff options
Diffstat (limited to 'mausezahn.8')
| -rw-r--r-- | mausezahn.8 | 22 |
1 files changed, 11 insertions, 11 deletions
diff --git a/mausezahn.8 b/mausezahn.8 index 0554753..1e67562 100644 --- a/mausezahn.8 +++ b/mausezahn.8 @@ -38,7 +38,7 @@ The interactive mode utilizes a completely redesigned and more flexible protocol framework called ``mops'' (mausezahn's own packet system). The look and feel of the cli is very close to the Cisco IOS^tm command line. .PP -You can start the interactive mode by executing mausezahn with the ``-x'' +You can start the interactive mode by executing mausezahn with the ``\-x'' argument (an optional port number may follow, otherwise it is 25542). Then use telnet(1) to connect to this mausezahn instance. If not otherwise specified, the default login/password combination is mz:mz, enable password is: mops. @@ -46,7 +46,7 @@ This can be changed in /etc/netsniff-ng/mausezahn.conf. .PP The direct mode supports two specification schemes: The ``raw-layer-2'' scheme, where every single byte to be sent can be specified, and ``higher-layer'' scheme, -where packet builder interfaces are used (using the ``-t'' option). +where packet builder interfaces are used (using the ``\-t'' option). .PP To use the ``raw-layer-2'' scheme, simply specify the desired frame as hexadecimal sequence (the ``hex-string''), such as: @@ -55,10 +55,10 @@ hexadecimal sequence (the ``hex-string''), such as: .PP In this example, whitespaces within the byte string are optional and separate the Ethernet fields (destination and source address, type field, and a short -payload). The only additional options supported are ``-a'', ``-b'', ``-c'', and -``-p''. The frame length must be greater or equal 15 bytes. +payload). The only additional options supported are ``\-a'', ``\-b'', ``\-c'', +and ``\-p''. The frame length must be greater or equal 15 bytes. .PP -The ``higher-layer'' scheme is enabled using the ``-t <packet-type>'' option. +The ``higher-layer'' scheme is enabled using the ``\-t <packet-type>'' option. This option activates a packet builder and besides the ``packet-type'' an optional ``arg-string'' can be specified. The ``arg-string'' contains packet-specific parameters, such as TCP flags, port numbers, etc (see example @@ -76,7 +76,7 @@ into the local mausezahn instance. If no port has been specified, port 25542 is used as default. .PP .SS -v -Verbose mode. Capital -V is even more verbose. +Verbose mode. Capital \-V is even more verbose. .PP .SS -S Simulation mode, i.e. don't put anything on the wire. This is typically combined @@ -129,9 +129,9 @@ As with the source address (see above) you can also specify a range or a DNS nam Create the specified packet type using the built-in packet builder. Currently, supported packet types are: ``arp'', ``bpdu'', ``ip'', ``udp'', ``tcp'', ``rtp'', and ``dns''. There is currently also a limited support for ``icmp''. Type -``-t help'' to verify which packet builders your actual mausezahn version +``\-t help'' to verify which packet builders your actual mausezahn version supports. Also, for any particular packet type, for example ``tcp'' type -``mausezahn -t tcp help'' to receive a more in-depth context specific help. +``mausezahn \-t tcp help'' to receive a more in-depth context specific help. .PP .SS -T <packet-type> Make this mausezahn instance the receiving station. Currently, only ``rtp'' is @@ -152,12 +152,12 @@ experimental bits (usually the Class of Service, CoS) and the Time To Live (TTL) can be specified. And if you are really crazy you can set/unset the Bottom of Stack (BoS) bit at each label using the ``S'' (set) and ``s'' (unset) option. By default, the BoS is set automatically and correct. Any other -setting will lead to invalid frames. Enter ``-M help'' for detailed instructions +setting will lead to invalid frames. Enter ``\-M help'' for detailed instructions and examples. .PP .SS -P <ascii-payload> Specify a cleartext payload. Alternatively, each packet type supports a -hexadecimal specification of the payload (see for example ``-t udp help''). +hexadecimal specification of the payload (see for example ``\-t udp help''). .PP .SS -f <filename> Read the ascii payload from the specified file. @@ -923,7 +923,7 @@ Send a DNS request as local broadcast (often a local router replies): mausezahn eth0 -t udp dp=53,p=c5-2f-01-00-00-01-00-00-00-00-00-00-03-77-77-\\ 77-03-78-79-7a-03-63-6f-6d-00-00-01-00-01" .PP -Additionally you may specify the lenght and checksum using the len and sum +Additionally you may specify the length and checksum using the len and sum arguments (will be set correctly by default). Note: several protocols have same arguments such as len (length) and sum (checksum). If you specified a udp type packet (via -t udp) and want to modify the IP length, then use the alternate |