diff options
Diffstat (limited to 'trafgen.8')
| -rw-r--r-- | trafgen.8 | 168 |
1 files changed, 168 insertions, 0 deletions
@@ -271,6 +271,174 @@ configuration, e.g. const16(0xaa) will result in ''00 aa''. Within c*() functions, it is possible to do some arithmetics: -,+,*,/,%,&,|,<<,>>,^ E.g. const16((((1<<8)+0x32)|0b110)*2) will be evaluated to ''02 6c''. .PP +iv) Protocol header functions: +The protocol header functions allow to fill protocol header fields by +using following generic syntax: +.in +8 +.sp +<proto>(<field>=<value>,<field2>=<value2>,...,<field3>,...) +.sp +.in -8 +.in +4 +If a field is not specified, then a default value will be used (usually 0). +Protocol fields might be set in any order. However, the offset of the fields in +the resulting packet is according to the respective protocol. +.sp +All required lower layer headers will be filled automatically if they were not +specified by the user. The headers will be filled in the order they were +specified. Each header will be filled with some mimimum required set of fields. +.in -4 +.sp +.in +4 +Supported protocol headers: +.sp +.I Ethernet +: +.B eth(da=<mac>, sa=<mac>, prot=<number>) +.sp +.in +4 +.B da|daddr +- Destination MAC address (default: 00:00:00:00:00:00) +.sp +.B sa|saddr +- Source MAC address (default: device MAC address) +.sp +.B prot|proto +- Ethernet type (default: 0) +.in -4 + +.I ARP +: +.B arp(htype=<number>, ptype=<number>, op=<request|reply|number>, request, +.B reply, smac=<mac>, sip=<ip4_addr>, tmac=<mac>, tip=<ip4_addr>) +.sp +.in +4 +.B htype +- ARP hardware type (default: 1 [Ethernet]) +.sp +.B ptype +- ARP protocol type (default: 0x0800 [IPv4]) +.sp +.B op +- ARP operation type (request/reply) (default: request) +.sp +.B req|request +- ARP Request operation type +.sp +.B reply +- ARP Reply operation type +.sp +.B smac|sha +- Sender hardware (MAC) address (default: device MAC address) +.sp +.B sip|spa +- Sender protocol (IPv4) address (default: device IPv4 address) +.sp +.B tmac|tha +- Target hardware (MAC) address (default: 00:00:00:00:00:00) +.sp +.B tip|tpa +- Target protocol (IPv4) address (default: device IPv4 address) +.in -4 +.sp +By default, the ARP operation field is set to request and the Ethernet +destination MAC address is set to the broadcast address (ff:ff:ff:ff:ff:ff). + +.I IPv4 +: +.B ip4|ipv4(ihl=<number>, ver=<number>, len=<number>, csum=<number>, +.B ttl=<number>, tos=<number>, dscp=<number>, ecn=<number>, +.in +16 +.B id=<number>, flags=<number>, frag=<number>, df, mf, da=<ip4_addr>, sa=<ip4_addr>, +.B prot[o]=<number>) +.in -16 +.sp +.in +4 +.B ver|version +- Version field (default: 4) +.sp +.B ihl +- Header length in number of 32-bit words (default: 5) +.sp +.B tos +- Type of Service (ToS) field (default: 0) +.sp +.B dscp +- Differentiated Services Code Point (DSCP, DiffServ) field (default: 0) +.sp +.B ecn +- Explicit Congestion Notification (ECN) field (default: 0) +.sp +.B len|length +- Total length of header and data (calculated by default) +.sp +.B id +- IPv4 datagram identification (default: 0) +.sp +.B flags +- IPv4 flags value (DF, MF) (default: 0) +.sp +.B df +- Don't fragment (DF) flag (default: 0) +.sp +.B mf +- More fragments (MF) flag (default: 0) +.sp +.B frag +- Fragment offset field in number of 8 byte blocks (default: 0) +.sp +.B ttl +- Time to live (TTL) field (default: 0) +.sp +.B csum +- Header checksum (calculated by default) +.sp +.B sa|saddr +- Source IPv4 address (default: device IPv4 address) +.sp +.B da|daddr +- Destination IPv4 address (default: 0.0.0.0) +.sp +.B prot|proto +- IPv4 protocol number (default: 0) +.in -4 +.sp +By default, if the lower level header is Ethernet, its EtherType field is set to +0x0800 (IPv4). If the lower level header is IPv4, its protocol field is set to +0x4 (IP-in-IP). + +.I UDP +: +.B udp(sp=<number>, dp=<number>, len=<number>, csum=<number>) +.sp +.in +4 +.B sp|sport +- Source port (default: 0) +.sp +.B dp|dport +- Destination port (default: 0) +.sp +.B len|length +- Length of UDP header and data (calculated by default) +.sp +.B csum +- Checksum field over IPv4 pseudo header (calculated by default) +.sp +.in -4 +By default, if the lower level header is IPv4, its protocol field is set to +0x11 (UDP). + +Simple example of a UDP Echo packet: +.PP +.in +5 + { + eth(da=11:22:33:44:55:66), + ip(daddr=1.2.3.4) + udp(dp=7), + "Hello world" + } +.in -5 +.PP Furthermore, there are two types of comments in trafgen configuration files: .PP 1. Multi-line C-style comments: /* put comment here */ |