1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
|
Broadcom STB "UPG GIO" GPIO controller
The controller's registers are organized as sets of eight 32-bit
registers with each set controlling a bank of up to 32 pins. A single
interrupt is shared for all of the banks handled by the controller.
Required properties:
- compatible:
Must be "brcm,brcmstb-gpio"
- reg:
Define the base and range of the I/O address space containing
the brcmstb GPIO controller registers
- #gpio-cells:
Should be <2>. The first cell is the pin number (within the controller's
pin space), and the second is used for the following:
bit[0]: polarity (0 for active-high, 1 for active-low)
- gpio-controller:
Specifies that the node is a GPIO controller.
- brcm,gpio-bank-widths:
Number of GPIO lines for each bank. Number of elements must
correspond to number of banks suggested by the 'reg' property.
Optional properties:
- interrupts:
The interrupt shared by all GPIO lines for this controller.
- interrupt-parent:
phandle of the parent interrupt controller
- interrupts-extended:
Alternate form of specifying interrupts and parents that allows for
multiple parents. This takes precedence over 'interrupts' and
'interrupt-parent'. Wakeup-capable GPIO controllers often route their
wakeup interrupt lines through a different interrupt controller than the
primary interrupt line, making this property necessary.
- #interrupt-cells:
Should be <2>. The first cell is the GPIO number, the second should specify
flags. The following subset of flags is supported:
- bits[3:0] trigger type and level flags
1 = low-to-high edge triggered
2 = high-to-low edge triggered
4 = active high level-sensitive
8 = active low level-sensitive
Valid combinations are 1, 2, 3, 4, 8.
See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
- interrupt-controller:
Marks the device node as an interrupt controller
- wakeup-source:
GPIOs for this controller can be used as a wakeup source
Example:
upg_gio: gpio@f040a700 {
#gpio-cells = <2>;
#interrupt-cells = <2>;
compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
gpio-controller;
interrupt-controller;
reg = <0xf040a700 0x80>;
interrupt-parent = <&irq0_intc>;
interrupts = <0x6>;
brcm,gpio-bank-widths = <32 32 32 24>;
};
upg_gio_aon: gpio@f04172c0 {
#gpio-cells = <2>;
#interrupt-cells = <2>;
compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
gpio-controller;
interrupt-controller;
reg = <0xf04172c0 0x40>;
interrupt-parent = <&irq0_aon_intc>;
interrupts = <0x6>;
interrupts-extended = <&irq0_aon_intc 0x6>,
<&aon_pm_l2_intc 0x5>;
wakeup-source;
brcm,gpio-bank-widths = <18 4>;
};
|
