1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
|
Analog Devices AD5592R/AD5593R DAC/ADC device driver
Required properties for the AD5592R:
- compatible: Must be "adi,ad5592r"
- reg: SPI chip select number for the device
- spi-max-frequency: Max SPI frequency to use (< 30000000)
- spi-cpol: The AD5592R requires inverse clock polarity (CPOL) mode
Required properties for the AD5593R:
- compatible: Must be "adi,ad5593r"
- reg: I2C address of the device
Required properties for all supported chips:
- #address-cells: Should be 1.
- #size-cells: Should be 0.
- channel nodes:
Each child node represents one channel and has the following
Required properties:
* reg: Pin on which this channel is connected to.
* adi,mode: Mode or function of this channel.
Macros specifying the valid values
can be found in <dt-bindings/iio/adi,ad5592r.h>.
The following values are currently supported:
* CH_MODE_UNUSED (the pin is unused)
* CH_MODE_ADC (the pin is ADC input)
* CH_MODE_DAC (the pin is DAC output)
* CH_MODE_DAC_AND_ADC (the pin is DAC output
but can be monitored by an ADC, since
there is no disadvantage this
this should be considered as the
preferred DAC mode)
* CH_MODE_GPIO (the pin is registered
with GPIOLIB)
Optional properties:
* adi,off-state: State of this channel when unused or the
device gets removed. Macros specifying the
valid values can be found in
<dt-bindings/iio/adi,ad5592r.h>.
* CH_OFFSTATE_PULLDOWN (the pin is pulled down)
* CH_OFFSTATE_OUT_LOW (the pin is output low)
* CH_OFFSTATE_OUT_HIGH (the pin is output high)
* CH_OFFSTATE_OUT_TRISTATE (the pin is
tristated output)
Optional properties:
- vref-supply: Phandle to the external reference voltage supply. This should
only be set if there is an external reference voltage connected to the VREF
pin. If the property is not set the internal 2.5V reference is used.
- reset-gpios : GPIO spec for the RESET pin. If specified, it will be
asserted during driver probe.
- gpio-controller: Marks the device node as a GPIO controller.
- #gpio-cells: Should be 2. The first cell is the GPIO number and the second
cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>.
AD5592R Example:
#include <dt-bindings/iio/adi,ad5592r.h>
vref: regulator-vref {
compatible = "regulator-fixed";
regulator-name = "vref-ad559x";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
ad5592r@0 {
#size-cells = <0>;
#address-cells = <1>;
#gpio-cells = <2>;
compatible = "adi,ad5592r";
reg = <0>;
spi-max-frequency = <1000000>;
spi-cpol;
vref-supply = <&vref>; /* optional */
reset-gpios = <&gpio0 86 0>; /* optional */
gpio-controller;
channel@0 {
reg = <0>;
adi,mode = <CH_MODE_DAC>;
};
channel@1 {
reg = <1>;
adi,mode = <CH_MODE_ADC>;
};
channel@2 {
reg = <2>;
adi,mode = <CH_MODE_DAC_AND_ADC>;
};
channel@3 {
reg = <3>;
adi,mode = <CH_MODE_DAC_AND_ADC>;
adi,off-state = <CH_OFFSTATE_PULLDOWN>;
};
channel@4 {
reg = <4>;
adi,mode = <CH_MODE_UNUSED>;
adi,off-state = <CH_OFFSTATE_PULLDOWN>;
};
channel@5 {
reg = <5>;
adi,mode = <CH_MODE_GPIO>;
adi,off-state = <CH_OFFSTATE_PULLDOWN>;
};
channel@6 {
reg = <6>;
adi,mode = <CH_MODE_GPIO>;
adi,off-state = <CH_OFFSTATE_PULLDOWN>;
};
channel@7 {
reg = <7>;
adi,mode = <CH_MODE_GPIO>;
adi,off-state = <CH_OFFSTATE_PULLDOWN>;
};
};
AD5593R Example:
#include <dt-bindings/iio/adi,ad5592r.h>
ad5593r@10 {
#size-cells = <0>;
#address-cells = <1>;
#gpio-cells = <2>;
compatible = "adi,ad5593r";
reg = <0x10>;
gpio-controller;
channel@0 {
reg = <0>;
adi,mode = <CH_MODE_DAC>;
adi,off-state = <CH_OFFSTATE_PULLDOWN>;
};
channel@1 {
reg = <1>;
adi,mode = <CH_MODE_ADC>;
adi,off-state = <CH_OFFSTATE_PULLDOWN>;
};
channel@2 {
reg = <2>;
adi,mode = <CH_MODE_DAC_AND_ADC>;
adi,off-state = <CH_OFFSTATE_PULLDOWN>;
};
channel@6 {
reg = <6>;
adi,mode = <CH_MODE_GPIO>;
adi,off-state = <CH_OFFSTATE_PULLDOWN>;
};
};
|
